2005 Proposed changes to Tasar Class Rules


Home		Site Map Index New Archive Search WTCA>Agendas>Revisions to proposed rule changes 2005
		Revisions to the proposed changes to the Tasar Class Rules Approved by the World Council, August 12,2005 The World Council has approved three revisions to the original list of proposed changes to the Tasar class rules - two proposed changes have been withdrawn, and one has been added. Regions and Districts are asked to voted on the revised changes (see below) as soon as possible Revised list of proposed changes to the Tasar Class Rules A - Hull weight A1. Amend the first sentence of rule D.3.1 to read as follows: D.3.1 "A minimum hull weight of 68 kg shall apply for class racing." Leave the rest of D.3.1 unchanged. Delete rule D.3.2. Comment: This change is to accommodate Julian’s request to builders re hull weight. B - Sails Rule changes required if mylar sails are adopted B1. Measuring two jibs This proposed change has been withdrawn. Measuring one dacron and one mylar jib should be permitted. B2. National letters and sail numbers Amend the first sentence of rule C.1.3 to read: “ On dacron sails the national letters shall be wholly between the 4th and 5th batten pockets from the head point and the sail numbers shall be wholly between the 3rd and 4th batten pockets from the head point.” Add a new second sentence to read: " On mylar sails the lower national letters shall be placed on the port side, approximately 50 mm above the 4th batten pocket from the head point, and the upper sail numbers shall be placed on the starboard side, approximately 50 mm below the 4th batten pocket from the head point.” Comment: The new section reflects the different batten placement in the mylar sails, ensures the letters and numbers are placed as on the trial sails, and places the letters above the numbers, as required by ISAF. B3. Measurement to head of jib Amend rule F.1.4 to read as follows: " For dacron sails, the measurement from the bearing point at the hounds to the aft head point of the jib shall not exceed 115 mm. This rule does not apply to mylar jibs." Comment: This rule is not applicable to mylar jibs. B4. Length of whisker pole This proposed change has been withdrawn. The maximum length for the pole with a mylar jib will be included at a later date. B5. Jib halyard and furler Add a new rule F.4.5. "When a mylar jib is used, a jib furler and swivel are not fitted, and a jib halyard and associated fittings, as supplied by the builder, are required. Any replacements of the supplied equipment are subject to all applicable rules, including C.2.4 and F.4.1.” B6. Mylar sails Add a new a new rule G.2.4: "The mainsail and jib may be of different materials, either mylar or dacron, but may not be changed during an event, except as permitted by rule C.2.1(c).” Comment: I am assuming that people may buy either a new mylar main or a new mylar jib first, so we should allow a dacron and a mylar sail to be used at the same time, at least initially. Obviously, this will happen less and less as time passes. If the sails can only be used as a pair (i.e. both dacron or both mylar), this rule should state: "The mainsail and jib must be of same material, either mylar or dacron.” B7. Leech take up Amend rule G.2.3 to read: “For dacron sails, leech take-up not extending more than 150 mm from the leech, for the purpose of compensating for stretch with use, is deemed to be a repair. The associated re-stitching may not extend more than 200 mm from the leech. Leech take up is not permitted for mylar sails.” Comment: Leech take up is not required with mylar sails. B8. Hull Weight – this proposal has been added Amend rule D.3.1 as follows: • delete "the furler and furler line" from the list of required equipment; • add "A furler and furler line" to the list of equipment that can be included if it is always used. If A1 is approved, D.3.1 would then read: " A minimum hull weight of 68 kg shall apply for class racing. Any ballast required to bring a hull up to the specified minimum weight shall be secured in the cockpit. Hulls shall be weighed dry with shroud pull-backs, hiking straps and all associated adjuster lines and shock cord erectors, inspection port covers and all permanently attached fittings in place. A furler and furler line, and a removable compass with a permanently attached mounting, may be included if they are always fitted when racing. All other equipment shall be removed prior to weighing." Comment: Boats using mylar jibs will not have a furler or line, and should not include these items when the hull is being weighed. Note: If proposal A1 is not approved, the words “of 68 kg” will not be included. The class rules are available here. Approved by World Council for circulation and voting 2005/07/04 Revisions approved 2008/08/12 Posted 2005/08/12
		Home Site Map Index New Archive Search WTCA>Agendas>Revisions to proposed rule changes 2005